Showing 289–304 of 371 results
-
SPEECH CONTROLLED HOME APPLIANCES
$84.14$63.71The main objective of the project is to develop a speech controlled home appliances that load is ON/off when a voice signal is sent from the users mobile. While the user sends the signal from the mobile, the remote operation is achieved by any smart-phone
-
Speech Recognised Notice board
$102.17$60.10Notice Board is primary thing in any institution / organization or public utility places like bus stations, railway stations and parks. But sticking various notices day-to-day is quite a difficult process. A separate person is required to take care of this notices display. This project deals about an advanced hi-tech wireless notice board.
-
SPEED CHECKER TO DETECT RASH DRIVING ON HIGHWAYS
$90.15$60.10The aim of this project is to develop a device to detect rash driving on highways and to alert the traffic authorities in case of any speed violation. Accidents due to rash driving on highways are on the rise and people are losing their lives because of others mistakes. In the present system, to detect rash driving the police has to use a handheld radar gun and aim at the vehicle to record its speed. If the speed of the vehicle exceeds the speed limit, nearest police station is informed to stop the speeding vehicle. This is an ineffective process as after detecting one has to inform the same and a lot of time is wasted.
-
SPEED CONTROL OF INDUCTION MOTOR USING ACPWM
$100.97$88.95This project attempts a new speed control technique for the single-phase a.c. induction motor. It presents a design of a low-cost; high-efficiency drive capable of supplying a single-phase a.c. induction motor with a PWM modulated sinusoidal voltage. The circuit operation is controlled by an 8051 family microcontroller.
-
Speed Control Of Induction Motor Using Firing Angle Control
$90.15$70.92The main object of this project is to develop speed control of two induction motor using firing angle control system which is helpful to control the speed of an induction motor using microcontroller
In this project, the zero-crossing point of the voltage waveform is detected by a comparator whose output is then fed to the microcontroller. Then, it provides the required delayed triggering pulses to a pair of TRIAC through an opto-isolator connected to this circuit. Finally, power is applied to the load through the TRIAC. Four push-button switches are interfaced to the controller for increasing and decreasing the AC power to the load. In this project, a lamp is used in the place of induction motor demonstration purposes. The motor speed variation depends on the power reduction.
-
SPEED CONTROL OF TWO INDUCTION MOTOR USING ACPWM
$126.21$103.37This project attempts a new speed control technique for the single-phase a.c. induction motor. It presents a design of a low-cost; high-efficiency drive capable of supplying a single-phase a.c. induction motor with a PWM modulated sinusoidal voltage. The circuit operation is controlled by an 8051 family microcontroller. The device is aimed at substituting the commonly used triac phase angle control drives. The circuit is capable of supplying a single-phase a.c. induction motor (or general a.c. inductive/resistive load) with varying a.c. voltage. The same as in triac control, the voltage applied to the load can be varied from zero to maximum value. On the other hand, it uses a pulse width modulation technique (PWM), and when compared with the phase angle control used for triacs, produces much lower high order harmonics.
-
STREET LIGHT THAT GLOWS ON DETECTING VEHICLE MOVEMENT
$90.15$60.10This project is designed to detect a vehicle movement on road to switch on only a block of street lights that are ahead of the vehicle, and to switch off the glowing lights when the vehicle passes away from the lights. This will help to save electrical energy.
-
SUBSTATION MONITORING OVER IOT
$126.21$105.78The purpose of this project is to acquire the remote electrical parameters like voltage, current and frequency and send these real time values over network along with temperature at power station. This project is also designed to protect the electrical circuitry by operating a relay.
