Showing 1–16 of 34 results
-
AC DIMMER OF TWO LOADS USING SINGLE CONTROLLER
$102.17$72.12This project is intended to attain AC dimmer of two loads using single controller. It is a renowned and aged technique of managing AC power, principally across linear loads for instance heaters brought into play in electric oven.
In this project, we are using a comparator for zero crossing detection which is fed as an interrupt to the arduino UNO3. Here, the arduino delivers the output based on the interrupt received as the reference for generating triggering pulses. Using these pulses, we drive the Opto-isolators for triggering the TRIAC to achieve integral cycle control as per the input switches interfaced to the arduino. In place of a linear load to be used in the output, a series motor or lamp can be used to verify the output. A lamp is provided in this project in place of a motor for demonstration purpose. The project output with a lamp appears to be a simple project of lamp flickering but the real objective is to verify in a CRO/DSO ,whether at the random switching also the load switches on at zero cross of the waveform or not. -
AC DIMMER TO CONTROL AC VOLTAGE, SPEED OF INDUCTION MOTOR OR HEATER COIL
$52.89$40.87A voltage controller, also called an AC voltage controller or AC regulator is an electronic module based on either thyristors, TRIACs, SCRs or IGBTs, which converts a fixed voltage, fixed frequency alternating current (AC) electrical input supply to obtain variable voltage in output delivered to a resistive load.
Induction motor speed control is done by varying the frequency of the applied voltage. Raising or lowering the voltage can have some speed control effects but these will be small, difficult to control, load-dependent, possibly cause the motor to overheat and, are not generally recommended.
-
ACPWM power control using 555IC and IGBT
$62.50$50.48This project attempts a new speed control technique for the single-phase a.c. induction motor. It presents a design of a low-cost; high-efficiency drive capable of supplying a single-phase a.c. induction motor with a PWM modulated sinusoidal voltage. The circuit operation is controlled by 555 astable multivibrator. The device is aimed at substituting the commonly used triac phase angle control drives. The circuit is capable of supplying a single-phase a.c. induction motor (or general a.c. inductive/resistive load) with varying a.c. voltage.
-
ANDROID CONTROLLED ROBOT
$84.14$64.91The project is designed to control the ROBOT by using a Android technology for remote operation using an transmitter as smart phone and receiver as Bluetooth device. The direction of the DC motor is directly proportional to the voltage applied across its terminals.
-
AUTO INTENSITY CONTROL OF STREET LIGHTS
$102.17$72.12Red Light Emitting Diodes (LED) replaces HID lamps in street lighting system to include dimming feature. A microcontroller of 8051 family is used to control the intensity by developing pulse width modulated signals that drives a MOSFET to switch the LEDs according to achieve desired operation.
-
Automatic Load Sharing By Parallel Transformer
$90.15$74.52Transformer is basically a static device which transfers the electrical power from one circuit to another circuit with desired change in voltage and current at constant frequency. It is only one device which operates at highest efficiency at full load condition. But abnormal condition occurs at overloading condition which may result in severe problem in future.
-
AUTOMATIC POWER FACTOR COMPENSATION FOR INDUSTRIAL POWER USE TO MINIMIZE PENALTY
$104.57$92.55The project is designed to minimize penalty for industrial units using automatic power factor correction unit. The micro-controller used in this project belongs to 8051 family. In this proposed system, two zero crossing detectors are used for detecting zero crossing of voltage and current.
-
Automatic power factor correction with measurement of real power ,reactive power, apparent power
$115.39$103.37Automatic Power Factor Correction with measurement of real power, reactive power, and apparent power. Two zero crossing detectors are used for detecting zero crossing of voltage and current.
-
DC MOTOR SPEED CONTROL USING 555 TIMER IC
$40.87$28.85This project is designed to control the speed of a DC motor using PWM control using 555 IC. The speed of the DC motor is directly proportional to the voltage applied across its terminals. Hence, if the voltage across the motor terminal is varied, then the speed can also be varied.
-
FLEXIBLE AC TRANSMISSION SYSTEM BY STATIC VARIABLE COMPENSATOR
$88.95$76.93In this project to improve power factor of transmission lines using static variable compensator. These were inefficient and because of large rotating parts they got damaged quickly. Static VAR Compensation under FACTS uses TSC (Thyristor Switched Capacitors) based on shunt compensation duly controlled from a programmed microcontroller.
This proposed system demonstrates power factor compensation using thyristor switched capacitors. The time lag between the zero voltage pulse and zero current pulse duly generated by suitable operational amplifier circuits in comparator mode are fed to two interrupt pins of the 8 bit microcontroller of 8051 family. Prior to the implementation of static variable compensator, power factor compensation was done by large rotating machines such as synchronous condenser or switched capacitor banks. -
Four Quadrant DC Motor Controls without Microcontroller
$73.32$51.69The main intention of this project is to control the speed of a DC motor in alternative directions using speed control unit and to operate the motor in four quadrants: ie, clockwise, counter clock-wise, forward brake and reverse brake
-
INDUSTRIAL POWER CONTROL BY INTEGRAL CYCLE SWITCHING WITHOUT GENERATING HARMONICS
$106.98$86.54This project is intended to attain vital cycle switching – a technique to get rid of complete cycle, cycles or fractions of cycles of an AC signal. It is a renowned and aged technique of managing AC power, principally across linear loads for instance heaters brought into play in electric oven. However, the concept of achieving the cycle stealing of voltage waveform by the use of microcontroller can be very precise as per the program written in assembly C language so that the actual time-average voltage or current experienced at the load is proportionately lower than the whole signal if applied to the load.
-
INDUSTRIAL POWER CONTROL BY INTEGRAL CYCLE SWITCHING WITHOUT GENERATING HARMONICS
$102.17$90.15This project is intended to attain vital cycle switching – a technique to get rid of complete cycle, cycles or fractions of cycles of an AC signal. It is a renowned and aged technique of managing AC power, principally across linear loads for instance heaters brought into play in electric oven. However, the concept of achieving the cycle stealing of voltage waveform.
