-
-
-
-
0 out of 5
SOLAR POWER BANK WITH WIRELESS CHARGING
$146.64 $134.62In our proposed system we are used wireless charging ,it is a type of charging method which uses an electromagnetic field to transfer energy through electromagnetic induction. Energy is transferred between devices (transmitter and receiver) through the process of mutual induction.
-
4.67 out of 5
Solar Power Vaccine Storage Refrigerator
$156.26 $141.84Large areas of many developing countries have no grid electricity. This is a serious challenge that threatens the continuity of the vaccine cold chain. The main alternatives to electrically powered refrigerators available for many years—kerosene- and gas-driven refrigerators—are plagued by problems with gas supply interruptions, low efficiency, poor temperature control, and frequent maintenance needs. There are currently no kerosene- or gas-driven refrigerators that qualify under the minimum standards established by the World Health Organization (WHO) Performance, Quality, and Safety (PQS) system.
-
-
-
4.33 out of 5
SPEECH CONTROLLED HOME APPLIANCES
$84.14 $63.71The main objective of the project is to develop a speech controlled home appliances that load is ON/off when a voice signal is sent from the users mobile. While the user sends the signal from the mobile, the remote operation is achieved by any smart-phone
-
4.67 out of 5
Speech Recognised Notice board
$102.17 $60.10Notice Board is primary thing in any institution / organization or public utility places like bus stations, railway stations and parks. But sticking various notices day-to-day is quite a difficult process. A separate person is required to take care of this notices display. This project deals about an advanced hi-tech wireless notice board.
-
4.31 out of 5
SPEED CHECKER TO DETECT RASH DRIVING ON HIGHWAYS
$90.15 $60.10The aim of this project is to develop a device to detect rash driving on highways and to alert the traffic authorities in case of any speed violation. Accidents due to rash driving on highways are on the rise and people are losing their lives because of others mistakes. In the present system, to detect rash driving the police has to use a handheld radar gun and aim at the vehicle to record its speed. If the speed of the vehicle exceeds the speed limit, nearest police station is informed to stop the speeding vehicle. This is an ineffective process as after detecting one has to inform the same and a lot of time is wasted.
-
-
4.25 out of 5
SPEED CONTROL OF FAN USING RF REMOTE
$79.33 $67.31The main intention of this project is to develop an fan motor speed control system which is helpful to control the speed of fan motor using TRIAC and RF communication.
-
4.00 out of 5
SPEED CONTROL OF INDUCTION MOTOR
$96.16 $63.71The main intention of this project is to develop an induction motor speed control system which is helpful to control the speed of an induction motor using controller
-
4.50 out of 5
SPEED CONTROL OF INDUCTION MOTOR USING ACPWM
$100.97 $88.95This project attempts a new speed control technique for the single-phase a.c. induction motor. It presents a design of a low-cost; high-efficiency drive capable of supplying a single-phase a.c. induction motor with a PWM modulated sinusoidal voltage. The circuit operation is controlled by an 8051 family microcontroller.
-
4.45 out of 5
SPEED CONTROL OF INDUCTION MOTOR USING ANDROID
$88.95 $76.93The main intention of this project is to develop an induction motor speed control system which is helpful to control the speed of an induction motor using TRIAC.
-
4.33 out of 5
Speed Control Of Induction Motor Using Firing Angle Control
$90.15 $70.92The main object of this project is to develop speed control of two induction motor using firing angle control system which is helpful to control the speed of an induction motor using microcontroller
In this project, the zero-crossing point of the voltage waveform is detected by a comparator whose output is then fed to the microcontroller. Then, it provides the required delayed triggering pulses to a pair of TRIAC through an opto-isolator connected to this circuit. Finally, power is applied to the load through the TRIAC. Four push-button switches are interfaced to the controller for increasing and decreasing the AC power to the load. In this project, a lamp is used in the place of induction motor demonstration purposes. The motor speed variation depends on the power reduction.