Showing 321–336 of 380 results
-
Supply Selection Using Arduino
₹13,300.00₹12,200.00Inverters are widely used in the domestic as well as industrial environments to serve as the second line of source in case of power cut from the electricity utility grids. However, due to the low capacity of the battery, the inverter dies out with the use of heavy load appliances.
-
SYNCHRONIZED TRAFFIC SIGNALS
₹12,500.00₹11,400.00The goal of this project is to develop a synchronized traffic signal system which can be used to synchronize the traffic signals at the junctions in the metropolitan cities wherein the green signal given at one traffic junction ismaintained at consecutive junctions through a serial communication.Vehiclesgetting the green signal at one junction move through the subsequent junctions as the green signals aremaintained throughout different junctions.
-
-8%Table Saw Using Drill machine
₹13,000.00₹12,000.00In this project we have created table saw by using Drill machine . drill machine is mounted on strong base table with nut & bolt system so that it can be assembled & dismantled easily. In drill machine chuck Cutter blade is tightened.On cutting surface Scale is sketched to identify and mark cutting width.Cutting surface made of plywood is attached on table by hinges and nut-bolt to make easy assembling & dismantling.
This project helps us to drill & cut plywood without any high investment.
-
TACHOMETER USING 8051 MICROCONTROLLER
₹6,800.00₹5,700.00The main objective of this project is to avoid physical contact between the motor shaft and tachometer by using a non-contact tachometer in order to make it convinient, while measuring the speed of aBLDC motor.Also using standard contact type tachometer may not feasible in some applications.
-
Temperature controlled load
₹3,800.00₹3,000.00This project is intended to develop a circuit to control a load automatically with a fixed temperature limit by using a thermistor sensor. Whenever the temperature increases beyond a certain limit, a lamp is switched off to bring the temperature to a normal value. Due to automatic switching on of the load, this system doesn’t require human involvement for monitoring the temperature of the load.
-
The Humidity and Temperature Measurement System using Arduino
₹4,900.00₹3,800.00The project is designed to develop an automatic humidity and temperature measurement system that displays temperature . In enrolment, use of proper method of measurement is important. The advantage of using this method is to reduce human intervention.
-
THIRD EYE FOR BLIND PERSON
₹6,500.00₹5,200.00The third eye for the blind is advancement with the assistance of the multidiscipline subjects like software engineering, hardware designing which encourages the visually impaired individuals to explore with speed and certainty by recognizing the object and person close- by deterrents utilizing the assistance of ultrasonic waves and inform them with a beep sound and audio assistance. The influenced ones have been utilizing the convention
white stick for a long time which in spite of the fact that being powerful, still has a considerable measure of weakness. These will be wearable innovations for the
blinds.
-
THREE PHASE TRANSMISSION LINE FAULT DETECTION
₹10,800.00₹9,800.00The Electric Power System is divided into many different sections. One of which is the transmission system, where power is transmitted from generating stations and substations via transmission lines into consumers. Both methods could encounter various types of malfunctions is usually referred to as a “Fault”. Fault is simply defined as a number of undesirable but unavoidable incidents can temporarily disturb the stable condition of the power system that occurs when the insulation of the system fails at any point. Moreover, if a conducting object comes in contact with a bare power conductor, a short circuit, or fault, is said to have occurred.
-
Three Phase Transmission Line Fault Detection Over IOT
₹12,700.00₹11,700.00The IOT base Transmission fault detection system can detect the fault when the line breaks down and it also shuts down the power supply through the faulty line until the operator shuts down the entire line once he confirms the fault. The system monitors the line fault in sequence for 3 lines namely R, Y, B Phases. Once if fault is detected the system sends the notification to the line monitoring station, it also provides the information about the faulty line and the distance at which the line is broken. The system is also capable of sending the line voltage to the monitoring station
-
Three Phase Transmission Line Fault Detection Over IOT Using ESP32
₹12,700.00₹11,700.00If we look at the present Transmission line fault detection system, there are several problems, few of which include lack of skilled labour, increased risks and also time consuming process. Automating a process is known to solve many or all of such problems faced in the conventional processes. This is one such attempt to create an easy and cost-effective solution which is applicable in the upcoming power transmission systems for Electricity providers and operators at various stages or stations.
-
Touch Sensor Base Dimmer
₹5,500.00₹4,000.00Red Light Emitting Diodes (LED) replaces HID lamps in street lighting system to include dimming feature. A Arduino is used to control the intensity by developing pulse width modulated signals that drives a MOSFET to switch the LEDs according to achieve desired operation.
-
TOUCHLESS ATTENDANCE SYSTEM USING ARDUINO
₹15,800.00₹14,000.00The application of biometric recognition in personal authentication enables the growth of this technology to be employed in various domains. The implementation of biometric recognition systems can be based on physical or behavioral characteristics, such as the iris,, fingerprint, and face. Currently, the attendance tracking system based on biometric recognition for education sectors is still underutilized, thus providing a good opportunity to carry out interesting research in this area. As evidenced in a typical classroom, educators tend to take the attendance of their students by using conventional methods such as by calling out names or signing off an attendance sheet.
